Table of Contents The Recovery Console is a special boot up method that can be used to help fix problems that are preventing your Windows installation from properly booting up into Windows. This method allows you to access the files, format drives, disable and enable services, and other tasks from a console prompt while the operating system is not loaded. It is suggested that the Recovery Console is to only be used only after Safe mode and the other standard startup options do not work. I feel that the Recovery Console is also useful in other situations such as removing malware files that start in both Safe mode and Standard Mode and thus not allowing you to delete the infection. This tutorial will guide you through the installation of the Recovery Console and how to use it. For those who are familiar with DOS or the command prompt, you will find the Recovery Console to be very familiar. For those who are not comfortable with this type of environment, I suggest you read through this primer in order to get familiar with this type of interface: Introduction to the Windows Command Prompt How to install the Recovery Console to your hard drive I recommend that you install the Recovery Console directly onto your computer so that if you need it in the future, it is readily available. The Recovery Console only takes up approximately 7 megabytes so there is no reason why you should not have it installed in case you need it. To install the Recovery Console on your hard drive, follow these steps: Now when you start your computer you will have an option to start the Recovery Console. How to start the Recovery Console To start the Recovery Console when it is installed on your hard drive you would do the following: To start the Recovery Console directly from the Windows XP CD you would do the following: When the Recovery Console starts it will ask for your Administrator password before continuing. In many cases when you have XP pre installed on your computer the Recovery Console will not recognize your Administrator's password. In these situations it is possible to edit a registry setting so that the Recovery Console does not ask for a password. This setting works on both Windows XP Home and Pro editions. To change this setting do the following: Now the Recovery Console will no longer ask for a password. Though the Recovery Console looks similar to a standard command prompt it is not the same. Certain commands work, while others do not, and there are new commands available to you. There is no graphical interface, and all commands must be entered by typing them into the console prompt with your keyboard and pressing enter. This may be confusing for those who are not familiar with this type of interface, but after doing a few commands it does becomes easier. The following is a list of the available commands that you can use in the Recovery Console. When using the recovery console you can type help followed by the command to see a more detailed explanation. For example: help attrib. Warning: To remove the Recovery Console you need to modify the Boot.ini file. Modifying this file incorrectly can prevent your computer from starting properly. Please only attempt this step if you feel comfortable doing this. To remove the Recovery Console from your hard drive follow these steps: The recovery console should now be removed from your system.
Simply allow it to continue and then when it is finished, you will be presented with a screen similar to the one below telling you so.
Remove the prompting of a password
How to use the Recovery Console
Attrib Changes attributes on a file or directory. Batch Executes commands that you specify in the text file, Inputfile. Outputfile holds the output of the commands. If you omit the Outputfile parameter, output appears on the screen. Bootcfg Allows you to modify the Boot.ini file for boot configuration and recovery. CD (Chdir) Change directory. Operates only in the system directories of the current Windows installation, removable media, the root directory of any hard disk partition, or the local installation sources. Chkdsk Checks a disk for drive problems or errors. The /p switch runs Chkdsk even if the drive is not flagged as dirty. The /r switch locates bad sectors and recovers readable information. This switch implies /p. Chkdsk requires Autochk. Chkdsk automatically looks for Autochk.exe in the startup folder. If Chkdsk cannot find the file in the startup folder, it looks for the Windows 2000 Setup CD-ROM. If Chkdsk cannot find the installation CD-ROM, Chkdsk prompts the user for the location of Autochk.exe. Cls Clears the screen Copy Copies one file to a target location. By default, the target cannot be removable media, and you cannot use wildcard characters. Copying a compressed file from the Windows 2000 Setup CD-ROM automatically decompresses the file. Del (Delete) Deletes one file. Operates within the system directories of the current Windows installation, removable media, the root directory of any hard disk partition, or the local installation sources. By default, you cannot use wildcard characters. Dir Displays a list of all files, including hidden and system files. Disable Disables a Windows system service or driver. The variable service_or_driver is the name of the service or driver that you want to disable. When you use this command to disable a service, the command displays the service's original startup type before it changes the type to SERVICE_DISABLED. Note the original startup type so that you can use the enable command to restart the service. Diskpart Manages partitions on hard disk volumes. The /add option creates a new partition. The /delete option deletes an existing partition. The variable device is the device name for a new partition (such as \device\harddisk0). The variable drive is the drive letter for a partition that you are deleting (for example, D). Partition is the partition-based name for a partition that you are deleting, (for example: \device\harddisk0\partition1) and can be used instead of the drive variable. The variable size is the size, in megabytes, of a new partition. Enable Enables a Windows system service or driver. The variable service_or_driver is the name of the service or driver that you want to enable, and start_type is the startup type for an enabled service. The startup type uses one of the following formats:
SERVICE_BOOT_START
SERVICE_SYSTEM_START
SERVICE_AUTO_START
SERVICE_DEMAND_START Exit Quits the Recovery Console, and then restarts the computer. Expand Expands a compressed file. The variable source is the file that you want to expand. By default, you cannot use wildcard characters. The variable destination is the directory for the new file. By default, the destination cannot be removable media and cannot be read-only. You can use the attrib command to remove the read-only attribute from the destination directory. The option /f:filespec is required if the source contains more than one file. This option permits wildcard characters. The /y switch disables the overwrite confirmation prompt. The /d switch specifies that the files will not be expanded and displays a directory of the files in the source. Fixboot Writes a new startup sector on the system partition Fixmbr Repairs the startup partition's master boot code. The variable device is an optional name that specifies the device that requires a new Master Boot Record. Omit this variable when the target is the startup device. Format Formats a disk. The /q switch performs a quick format. The /fs switch specifies the file system. Help If you do not use the command variable to specify a command, help lists all the commands that the Recovery Console supports. Listsvc Displays all available services and drivers on the computer. Logon Displays detected installations of Windows and requests the local Administrator password for those installations. Use this command to move to another installation or subdirectory. Map Displays currently active device mappings. Include the arc option to specify the use of Advanced RISC Computing (ARC) paths (the format for Boot.ini) instead of Windows device paths. MD (Mkdir) Creates a directory. Operates only within the system directories of the current Windows installation, removable media, the root directory of any hard disk partition, or the local installation sources. More/Type Displays the specified text file on screen. More will display a text file one page at a time, while Type displays the entire text file at once. Rd (Rmdir) Removes a directory. Operates only within the system directories of the current Windows installation, removable media, the root directory of any hard disk partition, or the local installation sources. Ren (Rename) Rename a file or directory. Operates only within the system directories of the current Windows installation, removable media, the root directory of any hard disk partition, or the local installation sources. You cannot specify a new drive or path as the target. Set Displays and sets the Recovery Console environment variables. Systemroot Sets the current directory to %SystemRoot%.
C:\cmdcons\bootsect.dat="Microsoft Windows Recovery Console" /cmdcons
Make sure you only delete that one entry.
Posted by
Unknown
In the Open: field type X:\i386\winnt32.exe /cmdcons , where X is the drive letter for your CD reader, and press the OK button. An image of this step can be found below:
Command
Description
0 comments:
Post a Comment